Forumsee logo
Forumsee » Boating

Boating

1 2 3 4 5 6 7 Next >>   25 50 75

Today

how about your opinion, if i change the rotor ship with voith schneider propeller, but the construction voith schneider becomes longer as rotor ship in general design?
I was wondering how many of you have ripped a hole in your boat from a stump or a log? I know its critical to avoid larger rocks, but I do not avoid the timber as much, should ...
I bought a 94 Merc 40 hp in early 2014. All was fine until late 2015 when the power pack went out causes cylinders 1 and 3 to go out. I get new power pack no problem then early ...
Hi all My boat has been continuously in the (fresh) water for the last 3 years. (It's a 2008/9 boat). I will be taking it out shortly for a leg service and I'm wonder...
Hi everyone, I'm going to buy a 3288. I'm looking at a nice 1990 well loved. Updated. New fuel tanks from Bayliner. New transmissions. BUT... It has 3000 hrs ! Is that...
My seat is about 3" lower than comfortable i ride sitting on my leg which goes numb. Is there a such thing as pedestal extension?
A simple solution to prevent guest from falling into the lower berth by leaning on the door and hatch. The rail is cut on an angle to match the left end stanchion and a bullet ...
My friend has a 1990 Cadorette and the drive is slipping at high power. It is a king cobra with a 5.7 4b He thinks the cone clutch is worn out. Two questions: Anyone...
Hi All, Bending of 120 mm plate with a radius 235 mm is not possible in our area?(No facilities.)So We have planned to bend 2 60 mm thk plate and weld it together. But H...
hello.. I'm from Indonesia. I am interested in examining the rotor ship, just that I do not quite understand about the rotor ship construction. I would like to ask the opinion...
1971 mercury 9.8 no spark on either plug,only in forward gear ,new coils new stator ,wires .when trottle handle is in netural no spark, forward gear lots of spark whats up with ...
Hi from a newbie... in the link I think I attached from another post, you can see a cam and roller with a throttle plate in "full throttle" position. In my picture attached, y...
I recently came across a 12? Eliminator pickle fork tunnel outboard hull. Or at least I think that?s what it is since it has no HIN number or ID plates on it. I?ve seen a couple...
Hi sorry if this is a stupid question but sterndrives are somewhat new to me! I have a SP-c drive that has holes at the end of the cavitation plate (top of raw water exhaust...
I need to add a 3 amp power line to the starboard cupholder at the dash. I have no idea where I can tap into an existing line or if I need to run a new line from the battery all...
Lower unit went out last summer model# 200stletf $3800 estimate to rebuild internet has plenty units $1200 to $2500 range found one on craigslist couple hours away at good price...
Hello first post please forgive if it's a repeat. I have a 1994 johnson fast strike that the tach will work intermittently along with the voltmeter ( indash) reading 17-18 volts...
While discussing a kicker for my 1701 Starcraft, it was recommended that I get a High Thrust motor. I bought a long shaft Tohatsu 9.8 hp four stroke motor. The std prop on that ...
Hello everyone, new to these forums but seems like a great place for advice. I recently purchased an older 14.5 foot semi-V RandallCraft fiberglass skiff. It has a skinny storag...
Hi folks, My name is Jeff. I'm a Park Ranger in Everglades. Recently, someone decided to dump a Winner 1850cc in the glades. I took up the challenge to investigate it. The HI...
Hello all....I have a 1997 Mariah shabah z252....7.4/br3......duel battery with switch....the boat runs great and smooth, all gauges work great as do lights, 12v ac plug-ins, ec...
Anyone launched near SH1 recently think I might have a look there this weekend and some info about a possible launch site would be much appreciated.
Raymarine is finally coming out with AXIOM (3D sonar) with only 1 transducer, and I almost wasted money on their old technology! So, I have been looking for a side imaging fish...
Hi I just picked up a boat and want to understand my wiring. Although it's kinda cobbled up I think I can explain it. The perko has lead 1 going to battery 1 positive, lead 2 go...
Does anyone use one of these controllers with a Hydrastar hydraulic/electric set up, are they compatible?
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

The windage of a block of flats!
The windage of a block of flats!
Fiberfix, in your emergency repair bag?
Fiberfix, in your emergency repair bag?
OMC 140 backfire when cranking over
OMC 140 backfire when cranking over
Cracking you tube films of round Britain sail by young lad.
Cracking you tube films of round Britain sail by young lad.
My "Blondie" Dinghy. Design by John bell
My "Blondie" Dinghy. Design by John bell
Repower 34' yacht with diesel AC gen-set & VFD
Repower 34' yacht with diesel AC gen-set & VFD
Respect for Scottish sailors
Respect for Scottish sailors
Respect for Scottish sailors
Respect for Scottish sailors

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more