Forumsee logo
Forumsee » Boating » Technical & maintenance

Boating technical topics

1 2 3 4 5 6 7 Next >>   25 50 75

Today

Having followed the threads on bonding inverter generators I bought a separate tail lead and bonded Earth and Neutral in the plug and marked it for Generator only. This appears ...
I have an upside down T shaped Stainless steel shroud plate and one corner is bent. It's 1/4 inch thick and the hole where the turnbuckle pin goes has worn slightly oval as a re...
I sent my A127 Alternator to be reconditions. It came back looking nice and I wired it up exactly how it came off but isn't working. Photo one is the original wiring. Photo 2 is...
Just bought a 12 volt £28 bilge pump. It says it will do 3700 gallons per hour. If its true thats very fast. I could understand it if it said 3700 Liters per hour. Anyone ...
Was discussing sounder frequency with a bloke recently and recalled an old cray fishermen once showed me how he would identify Crays on the march by using 50 - 55 KHz with lot...
hi guys ok I took out my 2 barrel carb off my merceuiser 2003 3.0l and rebuilt it.. pretty easy but I have couple questions and issues The replacement accelerator pump is a lit...
After a full day of removing the outdrive, boots,gimbal bearing, pulling in new trim senders I went to put in my new gimbal bearing. I used an alignment tool that came with an ...
Has anyone experienced Cruise control Error? I got an error message while pulling a wakeboarder and the engine began hesitating. This only happens when in cruise control mode. ...
Good afternoon fellow fishing people. I'm not happy, I'm staying at South Durras (just nth of Batemans Bay - which I have done annually for a bloody long time) I've got a...
I can raise it up even with the cabin. I have two lead sails, suitable for self tacking. I am wondering if I will need a bar, solid anchor point running the width, or if ...
Hi all, Does anyone have any specs or history on the inter ? They used to be pretty common but I can find very little online about them. Bit concerned they might be pass...
So... how's everyone doing tonight? Well, I'm looking for some advice. There's a crack running horizontal across my transom. I've replaced wood transoms multiple times, but n...
Usually try to use the manufacturers recommended motor oil for all my vehicles. My new Silverado suggests AC Delco 0W20 Semi Synthetic. I went to all local auto parts today...
I have a new Garmin 1242xsv that came with the CV52HW-TM transducer. I want to add a 2nd unit, a 7608xsv. Will the existing transducer be ok? As always, thanks
TRYING TO REMOVE TRANS.ONLY BEEN ON 4 MONTHS.FOLLOWED INSTRUCTIONS TO NO AVAIL.EVEN HITTING UP WITH RUBBER MALLET.SCARED TO HIT REAL HARD,DON'T WANT TO BREAK IT.CHANGING FISHFIN...
So my boat needs a full new helm setup. I'm looking at dual 12" screens or possibly one 12" and one 9/10". Want radar, sonar, plotter, AIS, and VHF. Would like to be able to use...
Just received new evo 3 and found a spec change from using forward scan directly to sonar port on evo 3 to now having to buy a separate sounder module... anyone know whats the d...
So I'm trying to connect my HDS 12 gen 3 plotter to my standard horizon gx1600 VHF and have the DSC function work properly. Is this going to work? I have read other post that sa...
Hi fellow boaters. The 50ah lithium ion battery in the picture is used for a trolling motor. I frequently connect/disconnect, so am using preferring the clamps (as shown) t...
Well I got a great deal on a 1996 intrepid 26/28 and I have been fixing her up little by little. Yesterday I finally dropped her off at the shop to get a new pair of suzuki 2...
I have a 87 Astro glass bass boat. The previous owner did not use the livewells accept for storage sometimes or a cooler. My question is which holes on the back of the boat do...
I want to install some new yahama analog gauges and I can't find any information on installing water temp, water pressure and oil pressure. I found two yahama pro-series II ana...
Hey all, I am the proud new owner of a 2010 Sea Hunt Triton 220(picture attached), with a 250HP Yamaha, with only 180 total hours on it. I owned a wake boarding boat befor...
I am having an intermittent problem with my 2000 250 ox66. Occasionally the motor will surge in the rpm ranges from 3500 to 4700. The surge causes +/- 300 rpm. The problem does...
I didnt want to start a thread until I was finished with the project. I find it more fulfilling to read a build thread from start to finish- to each their own. I bought t...
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

Rollover test - cool stuff
Rollover test - cool stuff
Rollover test - cool stuff
Rollover test - cool stuff
new simrad s5100
new simrad s5100
Building a freeman 42
Building a freeman 42
225 OX66 problem... what does everyone think?
225 OX66 problem... what does everyone think?
yamaha F350 VS verado 350 ...the test !
yamaha F350 VS verado 350 ...the test !
A rather lovely model Riva
A rather lovely model Riva
stupid question about what "2 meter" and 70cm bands mean VS freq.
stupid question about what "2 meter" and 70cm bands mean VS freq.

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more